#include

#include "stm8l15x.h"

#include "iostm8l051f3.h"

#define LED_GPIO_PORT GPIOA

#define LED_GPIO_PINS GPIO_Pin_2 | GPIO_Pin_3

#define ADC1_DR_ADDRESS ((uint16_t)0x5344)

#define BUFFER_SIZE ((uint8_t) 0x02)

#define BUFFER_ADDRESS ((uint16_t)(&Buffer))

#define ASCII_NUM_0 ((uint8_t) 48)

#define ADC_RATIO ((uint16_t) 806)

#define SampleADC ((uint8_t) 0x0A)

uint8_t Buffer[4] = {0, 0, 0, 0};

uint16_t ADCdata = 0;

uint16_t ADCvalue = 0;

unsigned char LED =1;

unsigned char c = 8;

uint16_t acode = 1234; //43 "+" 0x2B;

void Delay(__IO uint16_t nCount)

{

while (nCount != 0)

{

nCount--;

}

}

//int putchar(int c)

//{

// while ((USART1_SR&0x80)==0x00);

// UART2_sendchar((u8)c);

// return (c);

//}

static void CLK_Config(void)

{

CLK_SYSCLKSourceSwitchCmd(ENABLE);

CLK_SYSCLKSourceConfig(CLK_SYSCLKSource_HSI);

CLK_SYSCLKDivConfig(CLK_SYSCLKDiv_1);

while (CLK_GetSYSCLKSource() != CLK_SYSCLKSource_HSI)

{}

CLK_PeripheralClockConfig(CLK_Peripheral_ADC1, ENABLE);

// CLK_PeripheralClockConfig(CLK_Peripheral_DMA1, ENABLE);

CLK_PeripheralClockConfig(CLK_Peripheral_TIM2, ENABLE);

CLK_PeripheralClockConfig(CLK_Peripheral_USART1, ENABLE);

}

static void GPIO_Config(void)

{

PC_DDR = 0X20;

PC_CR1 = 0X20;

PA_DDR = 0X0C;

PA_CR1 = 0X0C;

}

static void USART1_Config(void)

{

// ADCvalue = USART1_DR;

USART1_BRR2 = 0x03;

USART1_BRR1 = 0x68; //16M/9600=683

USART1_CR2 = 0x0C; //Transmitter & receiver enable

}

static void ADC_Config(void)

{

ADC1_CR2 = 0x27; //risign edge, trigger 3, sampling time 384

ADC1_CR3 = 0x10; //16channel

// ADC_ChannelCmd(ADC1, ADC_Channel_17, ENABLE);

}

void TIM2_Config(void)

{

TIM2_PSCR = 0x07; // 应是16，但只能置三位，所以是111 fCK_PSC / 2(PSC[2:0]).

// TIM2_PSCRL = 0x3F; // PSCR=0x1F3F，f=8M/(0x1F3F+1)=1000Hz，每个计数周期1ms

TIM2_ARRH = 0x00; // 自动重载寄存器ARR=0x01F4=500

TIM2_ARRL = 0x18; // 24X4us=96us 每记数500次产生一次中断，即500ms

TIM2_IER = 0x01; // 允许更新中断

TIM2_CR1 = 0x05; // 计数器使能，开始计数,只允许更新中断请求

}

void Delay (uint16_t nCount);

//#pragma vector = ADC1_EOC_vector

//__interrupt void ADC1_EOC(void)

//{

// ADCdata = ADC_GetConversionValue(ADC1);

// }

#pragma vector =TIM2_OVR_UIF_vector

__interrupt void TIM2_OVR_UIF(void)

{

asm("sim");

static uint8_t measurements = SampleADC;

static uint32_t accumulator = 0;

uint32_t average = 0;

uint16_t factor10 = 1000;

int8_t i ;

ADCdata = 0;

TIM2_SR1 = 0x00; //Clear UIF

ADC1_SR = 0x00; //Clear EOC

ADC1_CR1 = 0x03; // EOC interrupt unable, software set start, ADC enable

// while (!(ADC1_SR & 0x01));

Delay(0x000F);

ADCdata = (uint16_t)(ADC1_DRH);

ADCdata = (uint16_t)((uint16_t)((uint16_t)ADCdata << 8) | ADC1_DRL);

accumulator += ADCdata;

if(measurements == 0)

{

LED= !LED;

measurements = SampleADC;

average = accumulator/SampleADC;

ADCvalue = (uint16_t)((uint32_t)((uint32_t)average * (uint32_t)ADC_RATIO) / (uint32_t)1000);

accumulator = 0;

while(!USART1_SR_TXE);

for (i = 3; i >= 0; i--)

{

Buffer[i] = (ADCvalue/factor10) % 10 + 48; //提取十进制每一位，并转换成ASCII码

factor10 = factor10 / 10;

while(!USART1_SR_TXE);

USART1_DR = Buffer[i]; //发送每一位，先发高位

}

while(!USART1_SR_TXE);

USART1_DR = 32; //发送空格

}

measurements--;

asm("rim");

}

void main(void)

{

asm("sim");

GPIO_Config();

GPIO_Init(LED_GPIO_PORT, LED_GPIO_PINS, GPIO_Mode_Out_PP_Low_Fast);

CLK_Config();

ADC_Config();

TIM2_Config();

USART1_Config();

//DMA_Config();

asm("rim");

while (1) {

PA_ODR_ODR2 = LED;

PA_ODR_ODR3 = LED; }

}